Get a quote

Fibre tools

OTDR fault distance calculator

The OTDR gives the distance along the glass. Correct it for the launch cord, the index setting, the fibre's extra length in the cable and the slack loops to find the spot on the ground.

From trace to trench
A cut black fibre cable in an open trench beside a measuring wheel and a marker peg on a grass verge
EVT 032 x nLight goes out and back
OTDR fault distance calculatorFrom the OTDR reading to the spot on the ground
Runs
In your browser
Sends
Nothing

01The trace

02The cable and route

Fibre length to the event
-
Round trip time
-
Cable sheath length
-
Search window
-
Route distance to the break
-

An OTDR measures the time light takes to reach a break and come back, and turns it into a distance along the glass. The cable on the ground is shorter than the fibre inside it, and some of it is coiled in pits, closures and on poles, so the dig spot is nearer than the trace says. This calculator makes those corrections.

The four corrections

  • Launch cord: if the trace is measured from the OTDR port and not from the end of the launch cord, take the launch cord length off.
  • Index of refraction: the OTDR works out distance from the group index it is set to. If that differs from the fibre's own index (on the cable datasheet, usually about 1.467 to 1.468 at 1310 and 1550 nm), the distance scales by the ratio: set index divided by true index.
  • Extra fibre length: in a loose tube cable the fibres lie in a helix, so they are longer than the sheath, often by somewhere around 0.5% to 2%. The datasheet or a test on a known length of the same cable gives the real figure. The sheath metre marks at each end of the route are the best check.
  • Slack: coils stored in handholes, at closures and on poles use cable without moving along the route. Add up the slack stored between the OTDR end and the break from the as-built drawings.

Narrow it down before you dig

Test from both ends if you can: two readings that agree on the same point give a far smaller window. Compare the trace with the as-built drawings and the sheath metre marks at the nearest closure or pit, and walk the route for signs of digging, a new post or a fallen pole. The search window here assumes the extra fibre length is within half a percent of the figure you give and the reading within 2 m. See fibre optic cable repairs and OTDRs and test equipment.

Why the trace distance is what it is

Light in glass travels at the speed of light divided by the group index, about 204 000 km per second. The OTDR halves the round trip: distance = speed of light x time / (2 x index). One kilometre of fibre takes about 9.8 µs out and back. A wrong index setting of 0.003 shifts a 10 km reading by about 20 m, which is why the setting matters on long routes.

A guide, not a design

These figures follow the published standards and common design values, and the calculators work in your browser. They are a guide for planning and checking quotes. The datasheets for your cable and optics, and the network designer or contractor, have the final word. Nothing you type here is sent anywhere.

Frequently asked questions

How accurate is an OTDR fault location?
The reading along the fibre is usually accurate to a metre or two, but the spot on the ground depends on the index setting, the extra fibre length in the cable and the slack stored along the route. With those corrected from the as-built drawings, a fault can usually be found within a few metres.
What index of refraction should I set on the OTDR?
The group index on the cable or fibre datasheet for the wavelength you test at. Standard single-mode fibre is usually about 1.467 to 1.468. If you don't know it, the calculator lets you correct a reading taken with another setting afterwards.
What is the helix factor of a fibre cable?
How much longer the fibres are than the cable sheath, because they lie in a helix inside loose tubes. It is often given as a percentage, somewhere around 0.5% to 2%; the datasheet or a test on a known length gives the real figure.
Why is the break nearer than the OTDR says?
Because the OTDR measures the fibre, which is longer than the cable, and because slack coils along the route use cable without covering ground. Both make the trace distance longer than the walk along the route.

More fibre calculators

Free quote request, no obligation

Request quotes for fibre optic cable repairs

Fill it in the way a fibre contractor would size up the job: the route and the cores, the fibres to splice, the homes to connect, the trench to dig, or simply how many. The planner works out the cable, drums, splices, splitters or duct and draws it as you type. Suppliers and contractors in your area quote you directly.

Fibre job sheetFibre Optic Cable Repairs
Job
81522
Date
2026-11-22
Cost to you
Free

01The job

02How many (optional, it helps the quote)

Your requestA guide

-
-
-
-
-
-
Estimate
-

A guide from your figures, not a quote.

03On site now

04Your list (optional)

  1. 01
  2. 02
Up to 12 lines: cable, cords, connectors, panels, closures, splices or work.
Needs and options

05Your details

Free and no obligation. By sending you agree that we may share your request with suitable fibre optic cable suppliers, installers and contractors. See our privacy policy.

Get a free quote