Get a quote

Installation & services

Proof, fibre by fibre, that the link works

Free quotes from fibre testing contractors across South Africa. One request, no obligation.

Loss, trace and a report
A closed OTDR case beside a launch fibre box and a patch panel with yellow cords in an outdoor cabinet
EVT 01Tier 2An OTDR trace on each fibre

Link sheet: Fibre Testing and Certification

LNK FIB 768
01Suits
New links, acceptance and fault finding
02How it is done
Power meter loss tests and OTDR traces
03Scope
One link to a whole estate network
04Check first
Results against the link's loss budget
05Lead time
Often within days of the request

Fibre testing is how you know a new link meets its loss budget and how you find out where an old one has failed. There are two levels. Tier 1 measures each fibre's end-to-end loss with a light source and power meter. Tier 2 adds an OTDR trace that shows every splice, connector and bend along the way. Before either, the connectors are inspected and cleaned. This page explains the tests, what a proper test report contains and when you need which. Send one request and testing and splicing teams near you quote directly.

Tier 1 and Tier 2 testing

Tier 1 uses a light source at one end and an optical power meter at the other (together often called an OLTS or loss test set) to measure the total loss of each fibre, plus its length and polarity. That number is compared with the link's loss budget: fibre loss per km at the wavelength, plus connectors and splices. Tier 2 adds an OTDR trace. The OTDR sends pulses down the fibre and reads the light reflected back, showing each event and the distance to it. Single-mode is usually tested at 1310 and 1550 nm, multimode at 850 and 1300 nm.

Launch fibres and bidirectional testing

An OTDR cannot see right next to its own port, its dead zone, so the tester connects a launch fibre of a few hundred metres to a couple of kilometres at the start, and a receive fibre at the far end, to measure the first and last connectors. A splice measured from one direction can look better or worse than it really is, because the fibres either side differ slightly. Bidirectional testing, from both ends and averaged, gives the true splice loss and is what most network specs ask for on backbones.

Inspect, clean, then connect

Dirty connectors are the most common cause of high loss. A tester checks each end face with a fibre inspection probe, graded against IEC 61300-3-35, and cleans it before mating it to anything. A visual fault locator, a red laser, shows breaks and tight bends close to the panel and helps trace fibres. Never look into a fibre or connector, even one that seems dark: the test light is invisible infrared.

PON testing and the test report

On FTTH networks, the tester checks loss through the splitters against the optics' budget, and can test live fibres at 1625 or 1650 nm through a filter. Every job should end with a test report per fibre: trace files and a summary you keep for acceptance and for later fault finding. Testing is often priced per fibre or per link, with travel and any re-testing after repairs as separate lines. Test gear must be calibrated regularly, so ask for the calibration date.

What to put in your request

  • Number of fibres and links to test
  • Single-mode or multimode, and wavelengths
  • Tier 1 loss tests or Tier 2 OTDR traces
  • Connector types at each end of the links
  • Report format and who it goes to

Fibre Testing and Certification for estates, offices, factories, mines, farms and more

  • Houses and home offices: a quick loss test on a link from the house to an outbuilding
  • Estates, complexes and body corporates: acceptance testing on a new estate network before the HOA signs it off
  • Offices, business parks and shops: test reports for new backbones between floors and buildings
  • Factories, warehouses and plants: testing armoured links to plant rooms and tracing faults after damage
  • Mines, quarries and heavy industry: OTDR traces on long links to find breaks and bad joints
  • Farms, wine estates and lodges: checking a long farm route and its splices before handover
  • Schools, campuses, hospitals and municipalities: certifying fibre in schools, hospitals and campus cabling projects
  • Data centres and server rooms: Tier 1 and Tier 2 tests on trunks, MPO links and patching
  • Network operators, ISPs and contractors: acceptance and PON testing on operator and wireless ISP builds

Frequently asked questions

Do you test fibre yourselves?
No. We are a free quote request service and do no testing or installation. We pass your request to independent fibre testers, splicing teams and installers in your area, and they quote you directly.
Do I need an OTDR test or is a power meter enough?
For a short indoor link, a Tier 1 loss test often satisfies the spec. For outdoor routes, links with splices along the way and anything you want to accept formally from a contractor, ask for Tier 2 OTDR traces too. The network designer or the equipment maker's requirements decide it.
What should a fibre test report show?
Each fibre's identity, the wavelengths tested, the measured loss against the budget, the length, and for Tier 2 the OTDR trace with each event and its loss. It should name the instrument and its calibration date and include the raw trace files, not just a printout.
Can testing find the fault on an existing link?
Yes. An OTDR shows the distance from the panel to a break or a bad splice, and a VFL finds faults near the end. The repair crew then measures along the route to find it. See fibre optic repairs.

Fibre Testing and Certification by province and city

More fibre supplies and services

Free quote request, no obligation

Request quotes for fibre testing

Fill it in the way a fibre contractor would size up the job: the route and the cores, the fibres to splice, the homes to connect, the trench to dig, or simply how many. The planner works out the cable, drums, splices, splitters or duct and draws it as you type. Suppliers and contractors in your area quote you directly.

Fibre job sheetFibre Testing and Certification
Job
79993
Date
2026-11-19
Cost to you
Free

01The job

02The fibres (optional, it helps the quote)

Splice trayA guide

-
-
-
-
-
-
Estimate
-

A guide from your figures, not a quote.

03On site now

04Your list (optional)

  1. 01
  2. 02
Up to 12 lines: cable, cords, connectors, panels, closures, splices or work.
Needs and options

05Your details

Free and no obligation. By sending you agree that we may share your request with suitable fibre optic cable suppliers, installers and contractors. See our privacy policy.

Get a free quote