Get a quote

Fibre tools

Fibre distance chart: how far each fibre carries each speed

Choose a speed and a fibre to see the standard reach, or check a link length against every fibre type at once.

Ethernet reach by fibre
Aqua multimode and yellow single-mode patch cords plugged into pluggable optics on a network switch in a server rack
EVT 05OM4400 m at 10G
Fibre distance chartStandard Ethernet reach by fibre type
Runs
In your browser
Sends
Nothing

01Your link

Standard reach
-
Fibres that work at this length
-
Your link
-
EthernetOM1OM2OM3OM4OM5OS2
100BASE-FX100 Mb/s, 1300 nm2 km2 km2 km2 km2 kmno
1000BASE-SX1 Gb/s, 850 nm275 m550 m550 m550 m550 mno
1000BASE-LX1 Gb/s, 1310 nm550 m550 m550 m550 m550 m5 km
10GBASE-SR10 Gb/s, 850 nm33 m82 m300 m400 m400 mno
10GBASE-LR10 Gb/s, 1310 nmnonononono10 km
10GBASE-ER10 Gb/s, 1550 nmnonononono40 km
25GBASE-SR25 Gb/s, 850 nmnono70 m100 m100 mno
25GBASE-LR25 Gb/s, 1310 nmnonononono10 km
40GBASE-SR440 Gb/s, 850 nm, 8 fibres on MPOnono100 m150 m150 mno
40GBASE-LR440 Gb/s, 1310 nm, 4 wavelengthsnonononono10 km
100GBASE-SR4100 Gb/s, 850 nm, 8 fibres on MPOnono70 m100 m100 mno
100GBASE-LR4100 Gb/s, 1310 nm, 4 wavelengthsnonononono10 km
100GBASE-ER4100 Gb/s, 1310 nm, 4 wavelengthsnonononono40 km

Reach from the IEEE 802.3 Ethernet standards. 1000BASE-LX on multimode needs mode conditioning cords. Many 1G single-mode optics are sold for 10 km. Lengths in red are longer than the standard allows for that fibre.

How far a fibre link can run depends on the speed, the optic and the fibre. Single-mode OS2 carries any speed for kilometres; multimode reach shrinks as the speed goes up, from 550 m at 1 Gb/s to about 100 m at 100 Gb/s, and older OM1 and OM2 drop out first.

Multimode or single-mode?

Inside a building or a data centre, multimode with short reach 850 nm optics has been the cheaper choice for links up to a few hundred metres. OM3 and OM4 carry 10 Gb/s to 300 m and 400 m; OM5 adds shortwave wavelength multiplexing but the same reach for standard optics. Between buildings, across a campus or a farm, or anywhere the link may need more speed later, single-mode OS2 is the safer cable: the same glass carries 1, 10 or 100 Gb/s over 10 km and more, and the optics now cost little more. See multimode fibre cable and single-mode fibre cable.

When the old fibre is the limit

Many older buildings have OM1 (orange jacket, 62.5 µm) or OM2 between floors. OM1 runs 10 Gb/s only 33 m and OM2 only 82 m, so a backbone upgrade often means new fibre rather than new optics. Check the print on the cable sheath before buying switches. Never mix 62.5 µm and 50 µm cords on one link: the mismatch adds a large loss.

Reach is not the only limit

The standard reach assumes the link stays inside its loss budget. A long multimode link with several patch panels can fail inside the distance if the connectors lose too much. Check the loss with the fibre loss budget calculator, and match the optic to the connector on the panel with the patch cord finder. For the optics themselves see media converters and SFP modules.

A guide, not a design

These figures follow the published standards and common design values, and the calculators work in your browser. They are a guide for planning and checking quotes. The datasheets for your cable and optics, and the network designer or contractor, have the final word. Nothing you type here is sent anywhere.

Frequently asked questions

How far can 10G run on multimode fibre?
With standard 10GBASE-SR optics: 33 m on OM1, 82 m on OM2, 300 m on OM3 and 400 m on OM4 or OM5. On single-mode OS2, 10GBASE-LR optics run 10 km and 10GBASE-ER 40 km.
What is the difference between OM3 and OM4?
Both are 50 µm multimode with an aqua jacket, but OM4 has more bandwidth, so it runs further at high speeds: 400 m instead of 300 m at 10 Gb/s, and 100 m instead of 70 m at 25 or 100 Gb/s.
How far does single-mode fibre go?
Standard 10 Gb/s and 100 Gb/s optics run 10 km (LR) or 40 km (ER) on OS2, and longer reach optics go further. Over those distances the loss budget sets the limit rather than the fibre's bandwidth.
Can I use single-mode optics on multimode fibre?
Not in general. Single-mode and multimode optics must match the fibre. The exception is 1000BASE-LX, which runs up to 550 m on multimode with a mode conditioning patch cord at each end.

More fibre calculators

Free quote request, no obligation

Request quotes for multimode fibre cable

Fill it in the way a fibre contractor would size up the job: the route and the cores, the fibres to splice, the homes to connect, the trench to dig, or simply how many. The planner works out the cable, drums, splices, splitters or duct and draws it as you type. Suppliers and contractors in your area quote you directly.

Fibre job sheetMultimode Fibre Cable
Job
70439
Date
2026-11-22
Cost to you
Free

01The job

02The route (optional, it helps the quote)

Route and loss traceA guide

-
-
-
-
-
-
Estimate
-

A guide from your figures, not a quote.

03On site now

04Your list (optional)

  1. 01
  2. 02
Up to 12 lines: cable, cords, connectors, panels, closures, splices or work.
Needs and options

05Your details

Free and no obligation. By sending you agree that we may share your request with suitable fibre optic cable suppliers, installers and contractors. See our privacy policy.

Get a free quote