Get a quote

Fibre tools

dBm to mW converter for optical power

Convert between dBm, milliwatts and microwatts, and see how much of the light is left after a loss in dB.

Power meter readings
A small pluggable optical transceiver and a duplex patch cord on a clean bench beside an optical power meter
EVT 090 dBmEquals 1 milliwatt
dBm to mW converterOptical power in dBm, mW and µW
Runs
In your browser
Sends
Nothing

01Power

02After a loss

Power
-
Light left after the loss
-
Power after the loss
-
In dBm
-

Optical power meters, SFP datasheets and network equipment give light levels in dBm: decibels compared with one milliwatt. 0 dBm is 1 mW, every 10 dB is a factor of ten, and 3 dB is about half. Losses in a link are in dB and simply subtract from the dBm figure.

The formulas

dBm = 10 x log10(power in mW), and power in mW = 10 to the power (dBm / 10). A loss of L dB leaves 10 to the power (-L / 10) of the light: 3 dB leaves half, 10 dB a tenth, 20 dB a hundredth. So a transmitter at -3 dBm through a link losing 20 dB reaches the receiver at -23 dBm, about 5 µW.

LossLight leftStarting at 0 dBm (1 mW)
0.5 dB89%-0.5 dBm, 891 µW
1 dB79%-1 dBm, 794 µW
3 dB50%-3 dBm, 501 µW
6 dB25%-6 dBm, 251 µW
10 dB10%-10 dBm, 1 µW
15 dB3.2%-15 dBm, 31.6 µW
17.1 dB1.9%-17.1 dBm, 19.5 µW
20 dB1.0%-20 dBm, 10 µW
28 dB0.16%-28 dBm, 1.58 µW
30 dB0.10%-30 dBm, 1 µW

Readings you will meet

On a GPON network, class B+ optics have the OLT sending +1.5 to +5 dBm and the home ONU working down to about -27 dBm, with overload at -8 dBm; a home reading around -18 to -24 dBm is usual. Short reach multimode and 10G single-mode optics typically launch between about -8 and 0 dBm. The datasheet for the optic gives its minimum launch power and its receiver sensitivity: the difference is its loss budget. Work out the link with the loss budget calculator.

Measuring safely

The light in a fibre is invisible, and high power or amplified links can harm your eyes. Never look into a connector or a cut fibre; use a power meter, or an inspection scope that views the end face on a screen. Clean every connector before measuring: dirt is the commonest cause of a bad reading. See OTDRs and test equipment and fibre testing and certification.

A guide, not a design

These figures follow the published standards and common design values, and the calculators work in your browser. They are a guide for planning and checking quotes. The datasheets for your cable and optics, and the network designer or contractor, have the final word. Nothing you type here is sent anywhere.

Frequently asked questions

How do I convert dBm to mW?
mW = 10 to the power (dBm / 10). 0 dBm is 1 mW, 3 dBm about 2 mW, -10 dBm is 0.1 mW and -30 dBm is 0.001 mW (1 µW).
What is the difference between dB and dBm?
dBm is an absolute power level, compared with 1 mW. dB is a ratio, such as the loss of a link or a connector. Subtract a loss in dB from a power in dBm to get the power after the loss.
What is a good fibre signal level in dBm?
It depends on the receiver. A GPON home ONU (class B+) works from about -8 to -27 dBm, so -18 to -24 dBm is typical. For other optics, stay between the receiver's sensitivity and its overload level on the datasheet, with about 3 dB to spare.
Why is my power meter reading lower than expected?
Usually a dirty or damaged connector, the wrong wavelength set on the meter, or a bend. Clean and inspect both ends, check the meter is set to the wavelength being sent, and measure again.

More fibre calculators

Free quote request, no obligation

Request quotes for OTDRs and fibre test equipment

Fill it in the way a fibre contractor would size up the job: the route and the cores, the fibres to splice, the homes to connect, the trench to dig, or simply how many. The planner works out the cable, drums, splices, splitters or duct and draws it as you type. Suppliers and contractors in your area quote you directly.

Fibre job sheetOTDR and Fibre Test Equipment
Job
81880
Date
2026-11-22
Cost to you
Free

01The job

02How many (optional, it helps the quote)

Your requestA guide

-
-
-
-
-
-
Estimate
-

A guide from your figures, not a quote.

03On site now

04Your list (optional)

  1. 01
  2. 02
Up to 12 lines: cable, cords, connectors, panels, closures, splices or work.
Needs and options

05Your details

Free and no obligation. By sending you agree that we may share your request with suitable fibre optic cable suppliers, installers and contractors. See our privacy policy.

Get a free quote